For new home users, in addition to the primary concern of the decoration issues, home wiring should also be carefully considered; especially for homes with more than two computers, considering the cable network arrangement of computer networks and ordinary home appliances, it will be related to whether the future easy to use. This article outlines the issues that should be considered and addressed for the kind of wiring issues that users are concerned about. >>>Home Intelligence Wiring includes content I. Preparation There are many places to pay attention to in home wiring. For example, the distance, direction, and position of weak current (such as network cable) and strong electricity (power supply line) should refer to the relevant national standards. The cable should be protected by pvc pipe and other pipes, and be in the corner. Use double round corners for easy exchange. However, on the other hand, ordinary users do not need to worry too much about cabling because the most popular 100M Ethernet in the home network is already a very mature technology. The corresponding Super Category 5 cable, rj-45 modules, and panels It is already quite cheap and the quality is relatively stable. The design goals of home network cabling are usually easy to achieve. It is advisable to draw a plan of the bedroom at the beginning and then mark all planned information points on the map. Then draw the lines that need to be connected to the map and calculate the lengths of the various cables roughly (the principle is rather long and not short). The purchase of materials is mainly based on pvc pipes and all kinds of wires. The requirements of wire rods are: solid and good quality. Second, home network cabling (weak line) In fact, building a network for your home is not an easy task, but it is never an unfinished task. As long as we carefully plan, implement, set up, step by step, and pay attention to some of the tricks, for their own home network is not difficult. Of course, this is only for wired networks, and if you use wireless to connect all your home computers, these problems do not exist. 1, the cost estimate First, take a look at a normal home computer network, the normal cost of the wiring phase: If an ordinary two-family home has two computers, a certain length of network cable, two panels, two standard modules, two junction boxes, pvc lines Slots, all these devices cost about 110 yuan. If we add the cost of retrofitting in the existing room structure and a network device (router) connected to the computer, it is estimated that it will cost around RMB 200-300. 2, wiring related issues to consider At present, the wired network has entered the Gigabit era, and the 100Mb network has become quite popular and the corresponding network equipment is relatively inexpensive. However, it should be noted that it is advisable to purchase a device that is compatible with its own network environment. In addition, because the users of broadband with adsl must access through the telephone line, so the location of the broadband access is limited, must move to the access point to expand the network. This involves the issue of how to route. Under normal circumstances, the wiring method can be divided into two types: the open line and the dark line: The dark line refers to burying the line in the wall. The dark line has relatively large restrictions on computer settings. Therefore, it is recommended that each room needs to have an interface. In addition, the dark line is usually embedded in the decoration. Although beautiful, it is difficult for ordinary users to complete. The open line is not very beautiful because it is on the surface of the wall. Therefore, before the wiring, the position of the computer and the line through which the network cable passes are usually determined by the principle that the distance is short and the number of holes is smaller. If you route along the walls and add a flat trough, you can be more hidden and beautiful. Trunking The next step is to connect the panel socket. If you use a board with a few meters of wire, it will also cause confusion in the entire room cable. It is recommended to use a slot fixed on the wall. Wiring panel It is easy to install and beautiful, but the position of the computer and the electrical appliance must be taken into consideration when the cable is being routed. There are cable and crystal heads, this topic has been mentioned several times. Do not try to choose low-priced products for low prices. Although amps, avaya, etc., have higher prices, for the network, stability is the most important. As for broadband routers and switches to be used for networking, it should be considered as practical as possible; that is, in terms of interface selection of such devices, it is advisable to have more than two devices that actually connect to the terminal. The interface is used for troubleshooting in the future. Third, household appliances network wiring (strong line) In the computer network wiring process, we must also pay attention to the line arrangement of household appliances. Due to the dangers of strong electric lines, it is not recommended that ordinary users make their own arrangements. Instead, arrangements should be made during the wiring of professional circuit installers. This requires some common-sense knowledge: 1. Regardless of the method used to arrange the circuit into the wall, attention should be paid to checking the connection of the wire before threading, and all joints should be made at the end to avoid repeated construction. 2. It is recommended to separate the strong and weak circuits separately because the power of the strong lines easily interferes with the transmission of the network cable signals, that is, configure different slots and sockets for them. 3. Before the construction, fully consider the electrical and lighting equipment required for each functional area, and use this as a basis to roughly calculate the cross-sectional area of ​​the corresponding wire for each road. Should try to use high-quality copper core sheath and install the junction box, in order to avoid aging and breaking, resulting in difficult panel installation. postscript: In summary, home network cabling is actually a slow and labor-intensive process. Before and during implementation, full consideration should be given to future use and upgrade needs, and sufficient adjustment and upgrade conditions should be reserved. Finally, it is worth mentioning that if there are multiple computers in the home, each computer network cable connected to the network equipment, it is recommended to make a logo, which facilitates future troubleshooting. In short, as long as the preparation of the pre-wiring, the heart of the wiring and the detection after the wiring, your home network must be satisfactory. Hydropower renovation electrical room socket home decoration home furnishings renovation home Smart Ceiling Fan,Intelligence Ceiling Fan,Five Blades Ceiling Fan,5 Blades Ceiling Fan Jiangmen MagicPower Electrical Appliances Co.,Ltd. , https://www.mpceilingfan.com