One of the secrets of judging whether it is solid wood furniture is: wood grain and frugality. For example, if a cabinet door looks like a pattern, then the corresponding position of the pattern changes. Look at the corresponding pattern on the back of the cabinet door. If it is a good match, it is a solid wood cabinet door.
Dinoa board furniture furniture pine wood furniture
First, verify the solid wood
One of the secrets of judging whether it is solid wood furniture is: wood grain and frugality.
For example, if a cabinet door looks like a pattern, then the corresponding position of the pattern changes. Look at the corresponding pattern on the back of the cabinet door. If it is a good match, it is a solid wood cabinet door.
In addition, looking at frugality is also a good way to identify solid wood: look at the location of the scarred side, and then look for the corresponding pattern on the other side.
Second, determine the species
Ordinary solid wood furniture usually uses beech, white oak, ash, beech, beech, rubber wood, beech wood, and precious mahogany furniture mainly uses rosewood, chicken wing wood, rosewood.
The market for solid wood furniture is confusing, and things like shoddy and confusing tree species often appear. It is better to buy brand-name products. At the same time, it should be noted that the price of wood is increasing day by day.
Third, observe the wood
Open the furniture cabinet door and drawer to observe whether the wood is dry, white, and whether the texture is tight and delicate. If you have furniture made of materials such as particle board, density board and primary molding board, open doors or drawers and smell any pungent odors.
Fourth, find defects
The main parts of furniture such as pillars and load-bearing bars connecting the pillars to the ground should not have large knots or cracks. The structure is firm, the frame must not be loosened, and no breaks or breaks are allowed.
All parts of the wood-based panels used in furniture should be sealed. All kinds of accessories must be installed without missing parts, missing nails, or nails.
V. Inspection intensity
The strength of the board can be pressed with your finger to feel the firmness of the board.
One side of the material should have a well-shaped skeleton to be fixed, if the skeleton is sparse, a surface will feel empty and the panel vibrates greatly; the drawer bottom plate applies hand pressure to test the strength, generally the bottom of the partition plate is used, and the area is large. The partition should be made of five-layer boards.
Six, check the interface
Heavier furniture should be protected by screws in the corners and glued. As for the backplane part, it must also check whether it is well-laid and screw it up.
Seven test slides
The drawers should be strong and tight, and tighten the screws on the inside. May wish to open the drawers, movable table tops, cabinet doors and other parts to see if it can ensure that they can use freely and connect properly.
Eight, touch the surface
Place your hands on the surface of the furniture and carefully inspect whether the polished surface is smooth. In particular, check the table legs and other parts for roughness, whether the paint is streaking or not, whether the corner paint is too thick and whether there are cracks or air bubbles.
When the panel is covered with thin wood and other materials, the color of the finished product should be similar to that of the product. The surface paint film of the product is not allowed to be wrinkled, sticky, or leak paint.
Link: Buying Furniture Should Follow Eight Principles to Make Furniture “Do as the Romans Doâ€
Evaluation: Aote Yaju Solid Wood Furniture Leads the Fashion Trend
Furniture Purchase Furniture Brand Three Tree Lacquer Furniture Wood Furniture Paint Door Price Redwood Furniture Drawer Cabinet Door
DTMADE has been committed to manufacturing cost-effective products for many years. The product line covers four major product series, Snow Blower, Lawn Mower, Leaf Blower, garden tools.
DTMADE product is designed to keep up with the derivation of the market, innovation and quality stablization always become the first goal we pursue.
DTMADE provides excellent service to each OEM customer, and every project is assigned to a dedicated project manager. It takes only 6-12 months from project inception to production launch.
Cooperating with us shift your business!
heavy duty snow blower,snow blower machine,electric snow blower,hot air snow blower
Dtmade Manufacturing Co., LTD , https://www.dtmade.com