Summer is a rainy season, especially for a lot of busy workers, it is easy to forget the time in the morning after opening the window. So once the rainstorms come, our floor will inevitably be affected. More likely, happy, leaking, neglected, the floor is soaked, the upset is deformed... Every year, some unfortunate people encounter the above problems. What should I do when the floor is soaked in water? Option 1: Remove the baseboard Applicable conditions: strengthen the floor soaking water Treatment plan: Whether it is a large area of ​​water or a small area of ​​water, Mr. Liu does not recommend lifting the laminate floor to dry, so it is easy to damage the laminate floor, which may cause serious consequences that cannot be reused. It is best to quickly drain the surface water of the floor, then remove the baseboard of the floor, reveal the expansion joints, and distribute the water vapor by the expansion joints. However, depending on the amount of water inflow, it usually takes about seven to fifteen days for drying. Products that are better or have not been soaked for a long time can recover on their own. If they cannot recover after fifteen days, they should be considered for replacement. Option 2: Pick up the wooden floor and put it in a "well" shape. Applicable conditions: the floor that was picked up after soaking in water Treatment plan: For soaking floors, it is important to dry the skin while keeping the floor as free as possible. After the surface water of the floor is wiped dry, it is placed in a “well†shape, and the weight generated by the lamination is used to prevent the occurrence of deformation. When placing the surface, pay attention to the reverse side of the floor to prevent the surface from being caused by rapid drying. Dry cracking, while paying attention to the sun can not be exposed to the sun, it should be placed in a ventilated place dry, in general, for better quality solid wood and multi-layer solid wood can be used again. In addition, in the event of water leakage, the floor after-sales service should be notified at the first time, and the staff will provide the best solution to the owner in combination with the floor's own situation. Option 3: One side leaks, both sides are ventilated Adapt to the disease: add keel, a small area of ​​water-immersed solid wood flooring Treatment plan: a small area of ​​water found in time, after the ground is cleaned, the board is picked up, the wet floor is dried and re-installed; if the water intake is slightly larger, not only the board at the leak is picked up, but also The opposite board should also be picked up in the direction of the keel arrangement to allow the internal air to carry away the moisture. If you can't determine the amount of water inflow, it's best to pick up the board in turn according to the flow direction of the influent water, and check the moisture condition. Option 4: suck with a high-power vacuum cleaner Adaptation to the disease: solid wood flooring with a small area of ​​water in a straight-through manner Treatment plan: If the water inflow phenomenon is found in a very short time, a high-power vacuum cleaner can be used to suck out the water vapor. However, if a large area of ​​water is poured, the floor should be lifted up and dried in the second way. At the same time, if the indoor moisture is large, if there is a condition that the dehumidifier can be installed indoors, the indoor moisture can be drained in a short time, but this operation scheme needs to have the floor dry recognition technology. Summary: In real life, with the continuous improvement of living standards, there are more and more owners who choose to use the floor for decoration. If you make an purchase, how to maintain it in your daily life, how can we solve the problem? These, we should all understand bit by bit, and pay attention to accumulate. Flap Wheel Machine Mounted wheel machine is for producing flap wheel with shaft,which can slice abrasive clothes and place small pieces automatically. more effecient than arranging the flaps manually.
working station: 1-4 stations
We distributes and wholesales various brands of Bonded Abrasives, Abrasive Sanding Disc, Cotton Buffing Wheels, Flap Disc Backing Pad, Flap Disc Adhesive , and Surface Conditioning Product etc, and enjoy a high position among consumers.
abrasive tool making machine, flap wheel making machine, automatic flap wheel machine, semi-automatic flap wheel machine, machine manufacturer Zhengzhou Jiading Abrasive Manufacturing Co.,Ltd , https://www.jiadingabrasive.com
Product Name: Flap wheel machine
Cut off machine white electric box size: 600*300*1200(mm)
Cut off machine size: 900*600*850(mm)
Feeding device size: 600*600*800(mm)
Total Power: 2.2KW
sevice: 1 year after-sales sevice, Lifetime Maintenance
This machine can make Mounted wheels diameter from 20mm-100mm
height: 15-50mm
Feeding length for abrasive clothes in pieces: (1-30)mm (It can be adjustable)
Feeding width: (20-30)mm
Abrasive Clothes No.: 30-100 pieces ( It can be adjustable)
Operator No.: 1 person
